To hang a picture frame, shelf, or any other object on your wall or ceiling, you need to learn how to drill first. Aside from this, you should also know how to install bolts and screws the right way. Otherwise, your picture could fall, the wall might crack, and other problems could happen.
Drilling and installing a bolt may sound pretty straightforward. Drill a hole, insert the bolt, and hang your object. But aside from these basic steps, you also need to consider other factors.
Learn How to Drill for Installing a Bolt
If you are planning to do some drilling and installation, take note of the following tips. These can help you ensure the success of your project:
1. Identify the Type of Wall or Ceiling
What type of material will you be drilling and installing into? Are you planning to drill into a wall or a ceiling? Different kinds of materials and surfaces require different types of tools:
Plaster walls have been used since the early 20th century. They start out as wooden strips that are shaped into frames.
The makers of these walls then add layer upon layer of plaster to these wooden frames until they reach the desired thickness.
A lighter alternative to the plaster wall is the drywall, which people began using since the late 1950s. This type of wall is built from a plaster sheet that is placed between paper.
Aside from plaster walls and dry walls, there are the harder types of walls. These include concrete as well as brick and mortar materials.
2. Determine the Weight of the Object
The weight of the object is a basic yet essential factor in drilling and installing bolts. If it is a picture, painting or a clock, then small or medium-sized bolts should be enough. But if you are planning to put up a cabinet or a shelf, then you are going to need bigger and stronger bolts.
3. Determine the Place Where you Plan to Hang the Object
Where do you want to hang your clock or painting? You need to determine the place where you want to hang your object. If you are putting it on the wall, consider the weight of the object and if there is a hanger at the back of the frame.
Meanwhile, if you are going to hang something from the ceiling, take note that this will need a stronger anchor. Furthermore, you should also take note of the weight of the object.
4. Mark the Exact Spot with a Pencil
You can never be too precise when it comes to drilling and installing bolts. After all, this will leave a permanent mark on your wall or ceiling. You do not want to make the mistake of drilling a hole into the wrong place!
To avoid making a mistake, use a pencil to mark the exact spot where you plan to drill. If your picture frame or painting contains several hooks at the back, then remember to measure them, too. The goal here is to make sure that your drilling and installing project will be perfect.
5. Prepare Your Tools
The primary tool that you will be using is your drill, which can be hand-operated or powered by electricity. Choose a bit that is the same size as your bolt and insert this into the drill. Then, place the bolt alongside the bit.
Aside from the drill, bit, and bolts, you might need other tools as well. Before you start, make sure that you have a hammer, hammer drill, and adjustable wrench at hand. You never know when you might need to use them.
6. Determine the Depth of the Hole
Before you start drilling, don’t forget to measure how deep the hole will be. To make sure that you get the right depth, mark the spot on the drill bit. This will save you the trouble of having to check the depth again and again.
When you drill too deep, you are only wasting the space, time, and effort. But when it is too shallow, your bolt or screw cannot go in. So it is important to get the right depth.
If you are going to drill into a concrete wall, your hole should be about one-fourth inch deeper than the bolt or screw. This will provide extra space for the dust that will accumulate as you drill.
7. Drill the Hole
When you are ready, hold the drill against the ceiling or wall and press the trigger carefully. Drill for about 10 seconds, then pull out. Keep on drilling and then pulling out until you reach the target depth.
Sometimes, you might have trouble drilling to your target depth because there could be too much dust inside. If this happens, run the bit in and out for a few times to clean out the dust. Try drilling again to see if this solved the problem.
In some cases, you might fail to reach your target depth despite cleaning out the hole several times. When this happens, consider moving the drilling location by a few inches. You can also consider decreasing the depth of your holes.
8. Keep a Steady Pressure
It is necessary to maintain a steady pressure whenever you are drilling. If you don’t press hard enough, the bit could slip off or you might drill in the wrong direction. Always keep your pressure steady to get the best results.
Moreover, take note of your drilling speed. If you drill too fast, you could break your tools. A slow and steady speed is always best for drilling holes.
9. Insert the Bolt
After drilling the hole, use your fingers or blow into it to remove the extra dust. Put the bolt into the hole, then tighten it using a nut driver.
Drilling and installing a bolt may seem easy, but there are many things that you should consider. The location of the hole, the type of wall material, and the object you will hang are all important. Likewise, you should also check your speed and pressure whenever you are drilling.
Drilling and installing bolts takes a lot of time and practice. If you do not get it right the first time, do not worry because you can get better with practice. Just remember to follow the tips given above and start drilling!